Post by jamirie on Dec 25, 2012 14:50:06 GMT -5
Hey there,
after a while fiddling with SPRINTER i wanted to go further and test MARLIN, as it seems to be more accurate.
I managed to compile and upload it to my RAMPS 1.3 Board (ok, not that hard ), but when i open Replicator G and choose the Klimentkip driver as normal it does connect to the Printer but gets stuck when i open the live control panel and press one of the buttons for an axis. Further it will not respond anyway...
(i changed the Baudrate in the Firmware's configuration.h file to 115200, just as described)
An error message appears in the command line of ReplicatorG that says
"Firmware reset with active commands!
[20:27:30] Received OK with nothing queued!"
I didn't find anything about that error message, may somebody of you guys knows???
Here's the ReplicatorG's command line:
[20:27:11] Loading simulator.
[20:27:11] Loading driver: replicatorg.drivers.reprap.RepRap5DDriver
[20:27:11] Connecting to machine using serial port: COM5
[20:27:11] Supports RC
[20:27:11] Initializing Serial.
[20:27:11] GCode sent. waiting for response..
[20:27:13] echo: external reset
[20:27:13] Unknown: echo: external reset
[20:27:13] Unknown: marlin 1.0.0
[20:27:13] echo: last updated: dec 25 2012 18:45:37 | author: stohn
[20:27:13] GCode sent. waiting for response..
[20:27:13] Unknown: echo: last updated: dec 25 2012 18:45:37 | author: stohn
[20:27:13] Unknown: compiled: dec 25 2012
[20:27:13] echo: free memory: 3130 plannerbufferbytes: 2464
[20:27:13] Unknown: echo: free memory: 3130 plannerbufferbytes: 2464
[20:27:13] Unknown: error:0
[20:27:13] Unknown: : extruder switched off. maxtemp triggered !
[20:27:13] GCode sent. waiting for response..
[20:27:15] echo:sd init fail
[20:27:15] Unknown: echo:sd init fail
[20:27:17] echo:sd init fail
[20:27:17] Unknown: echo:sd init fail
[20:27:18] Received OK with nothing queued!
[20:27:18] Ready.
[20:27:18] Yes, I have a Realtime Control feature.
[20:27:18] Supports RC
[20:27:22] Supports RC
[20:27:24] Unknown: x:0.00y:0.00z:0.00e:0.00 count x: 0.00y:0.00z:0.00
[20:27:25] Unknown: x:0.00y:0.00z:0.00e:0.00 count x: 0.00y:0.00z:0.00
[20:27:26] Unknown: x:0.00y:0.00z:0.00e:0.00 count x: 0.00y:0.00z:0.00
[20:27:27] Unknown: x:0.00y:0.00z:0.00e:0.00 count x: 0.00y:0.00z:0.00
[20:27:28] Unknown: x:0.00y:0.00z:0.00e:0.00 count x: 0.00y:0.00z:0.00
[20:27:29] Unknown: x:0.00y:0.00z:0.00e:0.00 count x: 0.00y:0.00z:0.00
(HERE I TRIED TO PRESS THE BUTTON FOR X- IN THE LIVE CONTROL PANEL, NEXT IS WHAT HAPPENS ACCORDINGLY:)
[20:27:30] Firmware reset with active commands! (NOW IT IS DISCONNECTED AND STUCK)
[20:27:30] Received OK with nothing queued!
[20:27:30] Unknown: x:0.00y:0.00z:0.00e:0.00 count x: 0.00y:0.00z:0.00
[20:27:30] Supports RC
Another issue came up earlier- My thermistor for the hotend is mistakenly recognized as the heated bed thermistor (i do not even have a heated bed, ReplicatorG and on my Sumpod's Display show it that way too). In exchange the temperature for the bed is shown as temperature of my hotend (always shows about 290°C!!!)
What could have happened here??? I remember there was a thread about how to change the hotend<--->heated bed thermistor tables in the official Sumpod Forum quite some time ago... (So the temperature of my hotend will again be displayed as such so i can heat it up again)
But it seems to be gone, i couldn't find it anywhere in the www. May somebody knows about that?
I really appreciate any help, thanks for reading and hopefully sharing your thoughts
Regards!
JamIrie
after a while fiddling with SPRINTER i wanted to go further and test MARLIN, as it seems to be more accurate.
I managed to compile and upload it to my RAMPS 1.3 Board (ok, not that hard ), but when i open Replicator G and choose the Klimentkip driver as normal it does connect to the Printer but gets stuck when i open the live control panel and press one of the buttons for an axis. Further it will not respond anyway...
(i changed the Baudrate in the Firmware's configuration.h file to 115200, just as described)
An error message appears in the command line of ReplicatorG that says
"Firmware reset with active commands!
[20:27:30] Received OK with nothing queued!"
I didn't find anything about that error message, may somebody of you guys knows???
Here's the ReplicatorG's command line:
[20:27:11] Loading simulator.
[20:27:11] Loading driver: replicatorg.drivers.reprap.RepRap5DDriver
[20:27:11] Connecting to machine using serial port: COM5
[20:27:11] Supports RC
[20:27:11] Initializing Serial.
[20:27:11] GCode sent. waiting for response..
[20:27:13] echo: external reset
[20:27:13] Unknown: echo: external reset
[20:27:13] Unknown: marlin 1.0.0
[20:27:13] echo: last updated: dec 25 2012 18:45:37 | author: stohn
[20:27:13] GCode sent. waiting for response..
[20:27:13] Unknown: echo: last updated: dec 25 2012 18:45:37 | author: stohn
[20:27:13] Unknown: compiled: dec 25 2012
[20:27:13] echo: free memory: 3130 plannerbufferbytes: 2464
[20:27:13] Unknown: echo: free memory: 3130 plannerbufferbytes: 2464
[20:27:13] Unknown: error:0
[20:27:13] Unknown: : extruder switched off. maxtemp triggered !
[20:27:13] GCode sent. waiting for response..
[20:27:15] echo:sd init fail
[20:27:15] Unknown: echo:sd init fail
[20:27:17] echo:sd init fail
[20:27:17] Unknown: echo:sd init fail
[20:27:18] Received OK with nothing queued!
[20:27:18] Ready.
[20:27:18] Yes, I have a Realtime Control feature.
[20:27:18] Supports RC
[20:27:22] Supports RC
[20:27:24] Unknown: x:0.00y:0.00z:0.00e:0.00 count x: 0.00y:0.00z:0.00
[20:27:25] Unknown: x:0.00y:0.00z:0.00e:0.00 count x: 0.00y:0.00z:0.00
[20:27:26] Unknown: x:0.00y:0.00z:0.00e:0.00 count x: 0.00y:0.00z:0.00
[20:27:27] Unknown: x:0.00y:0.00z:0.00e:0.00 count x: 0.00y:0.00z:0.00
[20:27:28] Unknown: x:0.00y:0.00z:0.00e:0.00 count x: 0.00y:0.00z:0.00
[20:27:29] Unknown: x:0.00y:0.00z:0.00e:0.00 count x: 0.00y:0.00z:0.00
(HERE I TRIED TO PRESS THE BUTTON FOR X- IN THE LIVE CONTROL PANEL, NEXT IS WHAT HAPPENS ACCORDINGLY:)
[20:27:30] Firmware reset with active commands! (NOW IT IS DISCONNECTED AND STUCK)
[20:27:30] Received OK with nothing queued!
[20:27:30] Unknown: x:0.00y:0.00z:0.00e:0.00 count x: 0.00y:0.00z:0.00
[20:27:30] Supports RC
Another issue came up earlier- My thermistor for the hotend is mistakenly recognized as the heated bed thermistor (i do not even have a heated bed, ReplicatorG and on my Sumpod's Display show it that way too). In exchange the temperature for the bed is shown as temperature of my hotend (always shows about 290°C!!!)
What could have happened here??? I remember there was a thread about how to change the hotend<--->heated bed thermistor tables in the official Sumpod Forum quite some time ago... (So the temperature of my hotend will again be displayed as such so i can heat it up again)
But it seems to be gone, i couldn't find it anywhere in the www. May somebody knows about that?
I really appreciate any help, thanks for reading and hopefully sharing your thoughts
Regards!
JamIrie